Sonic pad usb not detected reddit. Any help would be appreciated.

Sonic pad usb not detected reddit Input Shaper Not Saving File to /tmp Folder This subreddit has voted to protest reddit's changes and will be set in read-only mode: https The sonic pad makes installing clipper easy, it guides you through the process, I just set up my sonic pad yesterday just consisted of flashing a sd card via sonic pad usb, putting it in the printer and turning it on and the sonic pad does the rest. *However* in the latest firmware update for the Sonic Pad, they changed the port to the upper port on the left side of the machine (not the back). If you put a little strip of tape on the correct pin of the usb cable, it no longer back feeds power. Foreign object detection only sometimes stops printing. A logitech C270 (720p) got roughly 7FPS. Once the cable is plugged in, the Logitech C615 will be turned on. I was also having some trouble with using the different videos instructions. Get support, learn new information, and hang out in the subreddit dedicated to Pixel, Nest, Chromecast, the Assistant, and a few more things from Google. Your other best option is to physically take the sonic pad to your router and plug in the Ethernet there and pull the files you wish, but it's going to be a lot of walking back and forth. log file and it basically says it is with some issue with serial or > did you flash the printer with a usb cable from the sonic pad or did you put a sd card into the printer with the . I just set it up on my E3 S1 Pro and previously set up on usb1 with usb connection. I saw a reviewer using the same model and they got a stable 15FPS without any setup. 25 there is a bug every time i download and switch off the pad and back on keeps downloading the same firmware over and over again i reached out to creailty they are aware of this issue and working on a new Literally just stopped, sonic pad was back to the home screen, no errors, nothing. I have the Sonic Pad and the CR10 Smart Pro I have no knowledge of klipper so was interested in using the Sonic Pad. The Nebula Pad retains the necessary information, so you do not need to keep the G Sensor attached to the printer continuously. All suggestions to fix this failed, i. I’m not pushing the speed as far as most and it’s still quite a bit faster and more precise. can anyone help. Or check it out in the app stores plugging the USB cable in the Sonic Pad's top left USB port, and then turning the Sonic Pad on and trying to flash it that way that seems to what worked flawlessly for me. Secondly if your printer is not maintenance and built square when you start to up the speeds stuff is going to fail or come loose you will see issues in the prints. It will say connect to USB 1 etc. It's not documented but I suspect Sonic Pad wants to talk to a 4. It seems that the firmware on the pas is for the 4. Tried to use my printer after updating the pad but the z offset was reset so I went to reset the offset but it was not working. Orca is really cool though. I went back and forward between Sonic Pad and stock firmware multiple times, without Sonic Pad there are no issues, but it just won't work with Sonic Pad, even tho the printer is officially supported. Eventually, I got a . *shrug * it's working now lol I appreciate the input though Reply reply Connect to the printer via USB 1 which is the top USB port on the side. Just downloaded the new update two days ago and since than it has caused so many issues with my sonic pad/S1 pro. Now put the printer. If that doesn't work and your laptop has a USB c connection, you might use a USB A to C connection between them, I've never tried it though. A factory reset also didn't My Ender 3V3SE connected to the same pad doesn’t suffer. everything is plugged in right as far as i can tell. Here, enthusiasts, hobbyists, and professionals gather to discuss, troubleshoot, and explore everything related to 3D printing with the Ender 3. I didn’t get key error 92, only key error 1. —— MCU errors during a print. The only way you'd get it "near 50% less" is if you had everything peripheral and somehow got extremely lucky with finding a new rpi4 at MSRP. It will be nice when they enable Creality Cloud connectivity. I was trying to lower the z level and the printer would move the extruder head down a little and Get the Reddit app Scan this QR code to download the app now Hardware serial port on Sonic Pad says ID: usb-FDDI_FT232R_USB_UART_A10JLHZ1-IF00-port0 Share Sort by: Best. Ive tried going into the config file and changing probe_with_touch_mode: false pin_up_reports_not_triggered: true pin_up_touch_mode_reports_triggered: false Maybe it corrupts a file if the sonic pad has another printer printing while it downloads files? I have no idea. cfg. This bracket fixed that problem, it stays mount all the time now. 7 board? I wonder if Creality is gonna update some of their printer profiles that are preloaded onto the Sonic pad. I'm not sure if running two at a time was causing it, but successfully printed two things (about 7 hours total) with no errors running one printer via USB My upgraded Ender 3 V2 with Sonic Pad and Nebula camera is working fine except for 2 things. Also noted croupt files in the stick, so it's fucked, not worth using USB as an extension to the SP file storage. The issue with the firmware was resolved by using a non creality SD card adapter to be able to write firmware to a freshly formatted SD card and then fully powering down printer and disconnecting from sonic pad and waiting 1 min and then inserting SD card to printer, powering on, and connecting to sonic pad. I Problem: Frequent random disconnects during printing when printer is connected to USB 1 on SonicPad. This seems to be an issue that pops up a lot. I have tried 3 different USB drives and I have an Ender 5 Plus and just bought the Creality Sonic pad for it. Guy on YouTube with 4k subscribers is working on a cheap, universal, mostly 3d-printable pellet extruder, and In order to connect the sonic pad (SP), you will need its IP address in your LAN. Replace with a proper USBC cable. 0 ports. I also am not a fan of how the sonic pad creates a bed, imo it probes way too fast and should be probing three times and taking avarages, Like Marlin. I have noticed that with the newer creality machines like the S1 line, have ferrite's installed on the power coming from the PSU & on the bed heater/thermister leads going to the main board. i had to use usb1, the top one on the side, if you use any other usb, it wont connect. I think the cable is just bad. org Members Online. Not sure if it matters, but I'm running the sonic pad using a ethernet cable, so I know wifi isn't the issue. I copied the file from the USB stick into an SD card and then inserted it into the printer, then connected the USB cable from the Sonic Pad to the printer and it worked that way. 46. Though the discussion is at best confusing with what appears to be it finally worked but I'm not sure what Glad it’s not just me. Even worse Sometimes web interface becomes unavailable despite the Sonic Pad is connected to WiFi and has IP address assigned. txt parameters with no luck. But asks me to flash the USB drive. the usb cable provided with the pad is dogshit, bin it and use a better usb to usb-c cable, i used one for my phone and im able to print, the provided cable caused errors midprint and starting prints. The normal procedure is to select your printer on the sonic pad (or one that has the same motherboard/chip) and then insert a micro SD card into a USB adapter on port 2 (bottom left) of the pad. had plugged the thermistor into wrong plug so the Sonic Pad had no idea what was going I've been successfully using the Sonic Pad for months. I'm not sure if it'll help but I just got my Ender 5 Pro working with my Sonic Pad last week. NG has eStep of 400. Pixel Stand 2 not working with P7P upvotes Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. The mini usb to usb-c adapter was defect. 52. I have the USB cable connected to the USB 1 port > to printer USB-C port. It started development in late 2014 and ended June 2023. Or check it out in the app stores   I can’t say which version they built the sonic pad with but it has been conveyed that it was built on a version prior to that feature I just started 3d printing a month or so ago. hex file I used USB cable from the Sonic Pad to flash the printer. One addition to this. Creality website, USB Fixer. the software hasnt been great but now its gotten worse. I have an Ender 3 Pro with the 4. I try-out different usb port. Klipper (sonic pad) recognize the camera and shows video but it cant record time lapse (see pic) 2. You can find the firmware on the manufacturer's website or community Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. Edit: No, that's not it. Locked post. I even reset and re-flashed the printer. I've basically done this on my Sidewinder X1, I removed the stock touch screen and replaced it Get the Reddit app Scan this QR code to download the app now. It will flash the SD card with the firmware file. When the cloud software and USB says not available. r/XMG_gg. Is my pad broken or is there something obvious I'm missing. I then went to the Other Printer tab and generated the flash file and flashed the printer firmware using Prusa slicer (Prusa said it was a success). Kindly note: The Creality Sonic Pad Serial Cable is required to ensure a stable connection with Ender-3 V3 SE. I changed thermistor no Get the Reddit app Scan this QR code to download the app now. Top Budget does not always mean "cheap", it means working within a reasonable price range but still using quality items, or the best Get the Reddit app Scan this QR code to download the app now. Make sure it is securely connected. I’ll try compressed air to the usb c as well to see if there’s dust or something. ive put print files on usb card reader but when plug in to pad nothing there. Also, even after a power cycle and restart, the Sonic pad will ask to resume the print but won't resume. I have never used Klipper. /r/StableDiffusion is back open after the protest of Reddit Also completely new to Klipper and Sonic Pad. I have a Microswiss NG on my E5+. I am stuck on the setup part that wants to update the firmware of the printer. 6. Testing is a pain, since there are 4 ports, and the trouble can be intermittent. Carefully I recently purchased a Creality Sonic Pad for my Ender 3 S1. The Beagle doesn't mind that your not using it Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. At least 3 or 4 different files. The set up in the book tells you to connect to the back USB but after mine failed to flash many times I was able to access the pad settings and download the newest update for the pad. I finally got the mount printed but when I tried to run the calibration from the Sonic Pad it kept erroring about hardware failures. I tried to plug it in the camera usb port (on Sonic Pad) and yet it's not detecting it. Edit: tried to connect with my old mainboard and still nothing i guess it’s the pad having issues Get the Reddit app Scan this QR code to download the app now. Got a serial cable for my Sonic Pad to connect to my Ender-5 S1. cfg files? With my Beagle Camera and Sprite Extruder Pro it was just as fast with as the Sonic Pad but without the Sonic headache! I've kept my Beagle plugged in because I can't find any hope with Sonic Pad Camera. I've got another cheap HD cam from Amazon and it worked directly :-/ I've tried all the USB places on sonic pad to get the webcam to work, but nothing helps. The Sonic Pad does not accept my Logitech C250 obvisouly. This is my second sonic pad and had no issues on my S1 Pro If you have the same problem using the same usb port move and add the printer on another port might be the alternative. I then found the printer on the Sonic Pad and attempted to flash the firmware, only get failure. Yes, put it in the top left USB port labeled USB1 BUT Disconnect everything else, like your camera and USB stick if you got those plugged in in the Sonic pad. Or check it out in the app stores I installed the Sonic Pad on my Ender 3 S1 Plus and got 5 print sessions out of it before I started getting various disconnect and thermal type shutdowns. There are two ways to print over the air. Flashed with Sonic Pad firmware Sonic Pad: When press the button to download klipper logs, it just open a blank window and nothing comes from it. Can still control through Web browser console. Followed all the steps, but no connection detected at all Tried every port on sonic pad but nothing works. I'm not a hardware expert, so please feel free to correct any errors. Connect the Sonic Pad to the Silent Board: Locate the Z-axis connector on the Silent Board and plug in the Sonic Pad's cable. 0. I saw a number of posts saying all you had to do was get the webcam set up and enable time-lapse. Also tried copying it to local will not go. Open comment sort options. Finally figured out my splicer settings were not changed so the gcodes were causing problems. (whoever says sonic pads are plug n play is full of shit). Install the Sonic Pad firmware: Download the specific firmware for your Ender 5 Plus with the Sonic Pad support. py file in klipper files /r/StableDiffusion is back open after the protest of Reddit killing open API access, which will bankrupt app developers Having the same issue now. A new cable did it! Thank you! Reply reply Thyshadow091421 ender 3 pro pause at height not working upvote Sonic pad not seeing BL Touch input on CR-10S Pro v2 . 2. Does anyone has a workaround? It’s pretty straightforward on Raspberry Pi, but looks like the functionality has been stripped off Sonic Pad it seems to completely disregard the webcam2. The command sequence above leaves the extruder stepper on, so you have to retract and feed the filament manually. The IP addresses will be : 192. Initially, I put the firmware on a USB and flashed from XLoader, but they removed the option to go to the Sonic Pad setup menu with the December 2022 update, so now I am stuck. I'm not an extremely experienced 3D printer guy. I just received a new Sonic Pad last night and I am having issues connecting it to the printer. It’s r/Zwift! This subreddit is unofficial and moderated by reddit Sonic Pad latest update was supposed to add CR-10 series its a HOT MESS. Hey all, I just got my Sonic pad for the S1 pro, I read the manual, checked the chip version of my printer (STM32F401), started the pad, updated it after connecting to wi-fi, selected the right printer, put the sd card US reader with the card on the sonic pad, it said to tl;dr - Try plugging your printer into the other ports on the Sonic Pad. I have re-flashed the screen and mainboard a couple times and can get it back to standard usable with the main screen. Can't see web interface and can't send objects to print via network. . Workaround- just to turn off and turn on the Sonic Same issue for me with a CR-10 PV2. board. The pad has several pre config options, not sure if the 5 plus is one or not as I'm setup with a full franken ender on my pad. I had switched back to Crealty slicer when I was having issues after the Cura update but after this I don't think it's on Cura's end. I am just glad they acknowledged it and should fix it. Get the Reddit app Scan this QR code to download the app now Recently got a sonic pad. I have downloaded all logs to a pendrive, but there are tons of files and folders, inside the folder printer_logs I found a klipper. You should see dots on the original printer screen. I haven't tried creating a custom printer profile yet. It seems the information isnt stated clearly. If either of those weren’t true, you wouldn’t get that screen, you’d just be unable to connect. My sonic pad is linked to my creality cloud app after the 5. I bumped the USB cable once with a pencil holder and it interrupted the print because the USB plug wiggled in the socket. Below are instructions to get it going. | Creality Cloud. It’s horror stories like these that have kept me from buying a A new Pi with everything is going to cost you more than a Sonic Pad. Two on the back. Most of the time, it's mounted and works. I've been using my sonic pad for the last few months without too much issue. Reddit's source for news, 1. I was thinking a bad USB cable, but your suggestion may be correct. i'm still trying things out as one of the obivious difference between the 2 is how loose the USB1 port is on the Hmm. I recently purchased a sonic pad to use with my Ender 3 V3 SE printer, once I had installed the updated sonic pad to have support with the Ender 3 V If that works let me know please. It's just not working as intended. I would really appreciate any ideas for troubleshooting. Case $10, USB wall plug $20, USB cable $10, SD Card $15, screen $50-$70~ That's already close to the cost of a Sonic Pad, sans the Pi. I have an Ender 3 Pro, with the aluminum version of the stock extruder, and this is not exceedingly difficult, though admittedly more of a pain than when the extruder is off, and rotates freely. I follow the installation steps up to the point it is supposed to connect to the printer but instead it errors out with no connection. I haven’t had any success on adding a secondary USB camera to Sonic Pad. I plugged it in, restarted the pad, and the camera works great. Sonic Pad has Max Neo as an option now. cfg you can connect it to a different port. But Max Neo does not have a USB port. It's not you, it's the Sonic Pad. Today after a loss of power, the sonic pad gets hung on the "System is preparing" screen. After I tested all the ports and documented which were bad, they sent me a new daughterboard, which was easy to install. Basically you cut the cord shorter and splice it back together. My Ender 3 S1 Plus have the ferrites, my Ender 3 V2 does not have them. My issues started about 11 months into my 12 month warranty, i put up with it till 12 months, then it stopped working totally. Specs and Settings (let me know if there is anything else that would be helpful to see): Creality Sonic Pad OS: Embedded Linux 1. in prusa slicer all I needed was to add 100x100, 200x200 to the line in printer settings for the gcode thumbnail and it works as it should. Now nothing works, and I’ve plugged it into another computer and it works fine. left side of the sonice pad Top one is USB1 Bottom one is USB2 on the Back of the pad Top one is USB3 Bottom one is USB4 if its the main printer it should be USB1 and yes the screen basically becomes useless, once you install the firmware for the sonic pad, i ended up entirely removing it If not, then I would suggest either returning it or doing a manual firmware update via usb. I have tried multiple times to flash my Ender-3 S1 Pro with the Sonic Pad firmware, each time it bricks and wont connect via usb to the Sonic Pad. I put STLs in the slicer add supports if necessary and make very slight tweaks in the settings (like temps, type of infill, and speed) and slice and fire away. Flashing it with the firmware on the creality sonic pad made the stepper motors not function correctly anymore. Thank you, if I keep having issues, I'll factory reset and try again. I watched some online videos where they unplug the sonic pad for some steps, tried that as well. ) time lapse is not working for me with a ToLuLu HD 1080 webcam. The original display stops working once the Klipper firmware is installed, so that's normal. 168. so this last iteration to get it working I did these steps in this order all in The camera and Sonic Pad, by default, create a video but it does not park the head and looks like a video being fast forward through. All of a sudden when I was using my Windows 10 Dell Inspiron 1500, my mouse stopped working, and I got a message that says “This USB device is not recognized”. Tried changing the webcam. I then try to connect the Sonic Pad to the printer and the Sonic Pad goes through the setup again. I somehow found an option to display the camera in live-view my last print but I can't seem to get that working for my latest one. Please Help!!! Edit - This is resolved by moving the USB to the port So i just got my new sonic pad and works great with usb stick. I have no idea what the problem is. If you use a normal usb cable, the sonic pad sends power back to the board and lights up the screen, but won’t run the printer. So I always pull it out and reinsert. The instruction manual tells you to plug the cable into the upper port. Basically make the firmware by connecting to the pad IP with putty, use winscp to connect to pad and transfer the firmware you made to your pc, and then copy that to the sd or usb stick to flash the printer. Any assistance would be appreciated! As mentioned, this is NOT A BUG, but a feature which was introduced later on. Some day I'll switch to it . According to Creality support this is not yet supported in the Nebula camera. Get the Reddit app Scan this QR code to download the app now. Plug USB cable into top left port on sonic pad I am not a fan of wireless devices per say. Any help would be appreciated. I had a defective USB daughterboard on my SP. i thought maybe it was a usb port problem since i didn’t have this with the 4. Well, I did that and still no time-lapse. randomly froze after finding a FW update on the usb stick (downloaded since it wasn’t doing it over WiFi) randomly froze multiple times even after the FW update on the pad Each time the blue light was still flashing, but the screen was completely unresponsive. I have also installed latest firmware update (NOV) on the pad and have deployed the firmware to the printer both via USB *AND* via XLoader. Only then will the Sonic pad "see" your printer and connect to it. I checked confirmed this by downloading the gcode file from the pad and then using exam diff pro to see if the files were different. Sonic Pad can talk to the CR6, bed calibration works, but it cannot spin up the part cooling fan and fails to set nozzle or bed temp - Klipper times out. hex file on my flash drive. Flashing it with the Ender 3V2 4. Or check it out in the app stores I then proceeded to install that printer and it created a bin file on my micro USB card, by following the Sonic Pad instructions. Anyways. With the resonance sensor calibration you should be able to up speeds pretty well as long as you can keep up flow. Next issues with running calibration. The 2 most common issues I see are the USB cable seem to have issues. any help will be greatly appreciated Using your ribbon cable that used to run to your Ender control pad, connect it to the port on the motherboard. MCU errors can be caused by the usb cable (try different ones) Having a webcam plugged in Having timelapse enabled Not taping off the 5v pin on the usb cable(not all printers have this issue) —— Where can I find printer. Then I went into the config and changed the port, finally moving the USB cable to the port on the back of the pad. I imported the Creative profiles and have not had the z offset issue any more. It has a blue area to click that shows which port is which. Usually even when I picked the wrong firmware the usb still connected. I finally decided to grab a Logitech C615. But always generates a snapshot of the detected foreign object. Bed leveling went well, but I changed to USB 3 and serial to clean up the wire mess and now I can't seem to The Sonic Pad has 4 USB 2. Current state is that I managed to get Klipper working and connected to the pad. 0 (alive) Firmware: V1. I can't seem to get past this point, and I have the I have been trying to figure out why the time-lapse wasn't working with my Sonic Pad and my Ender-5 S1. Only an Micro SD port. Apollo was an award-winning free Reddit app for iOS with over 100K 5-star reviews, built with the community in mind, and with a focus on speed, customizability, and best in class iOS features. All the resource intensive processing of G-Code happens on the Sonic Pad, and the mainboard only translates the commands from the Sonic Pad into movements. Everything is working but it's severely underextruding. The unofficial but officially recognized Reddit community The problem I'm having is when connecting the pad to the printer after the flash regardless of what usb port I use (I know the instructions say to use usb port 1) the sonic pad will eventually tell me the printer is not ready and the klippy host software is attempting to connect. Extract the downloaded archive file to the root of the usb stick and plug it into the bottom left USB port and turn it on (maybe also top left). Previously worked just fine. I also tried using both USB ports 1 and 2 on side of Sonic Pad. its not a good cable. sonic pad webcam isn't working upvote r/XMG_gg. 7. I tried formatting it in both FAT 32 and NTFS but the sonic pad still doesn't recognize it. I've seen many tutorial videos on how to install it but it seems they're all for the Ender 3 lineup, when you select Ender 5 Plus, it asks to install the USB cable from the pad to the printer, unlike all the Ender 3 videos where they're asked to install the USB stick to the pad. Go to SP config LAN and WiFi to retrieve that info. However, I ended up removing the USB stick it came with and it booted right up. " Share Sort by: After initial setup you can edit the printer. 3 CR6 but we have early Kickstarter so 4. i’ve probably tried more stuff but i have a sonic pad, but now I recalibrate the Z probe and after a restart the sonic pad cant connect my printer anymore. 5. Or check it out in the app stores I juggled the USB A side around to other USB ports on the Sonic pad until eventually nothing worked at all. Oddly enough, I can't get it to do timelapses. Well, big shocker It just flat out did not work. If you look it up everyone recommends. I just removed the useless display after setting up the Sonic Pad. Issues here too, thumb drive flashes, you think it's mounded, but when you click, it says not detected. Install the Logitech C615 I also deleted the printer from “select printer” menu (very top line of sonic pad, small font), then cold booted the sonic pad a couple times (I suppose there’s also a factory reset option somewhere in advanced options, too). I can see the preview on the pad and on my web UI. During a somewhat recent update to my Sonic Pad I ran into a similar problem because when multiple printer support was added, a "default" USB port was defined, and if you didn't have your sonic pad firmware 1. I tried a 1080p webcam and got about 2FPS. Sonic 8k mini not recognizing USB anymore . Community for owners of the Creality Sonic Pad. you need two sizes for the thumbnail, the one on the printer screen and the one the for the file. I have the correct IP i can get into the web interface. I plugged it into a different port, and that worked for a little bit. If dots show up then make sure that you have the printer on USB 1, which is the top left port. With the Sonic Pad being so new I expected some minor issues and multiple updates. I have 4 LK5 Pros and have successfully flashed them many times from the Sonic Pad. txt configuration file and it also seems to ignore any settings to it (resolution, but etc). Check Klipper out on discord, discourse, or Klipper3d. Is the stick formatted Fat32? I would try that first, making Since then I am not able to get any USB connection - neither to the printer, nor does the light of the USB-stick indicate that it accesses it (it is constantly red/on). Restarting the printer or re-slicing doesn't help. My guess is incorrect Rotation Distance. I have a Ender-3 V3 KE and if I connect it and just leave the printer for a bit, it does detect the sensor. Added support for USB peripherals (mouse/keyboard) Modify the net bed points directly on the PAD UI The extruder can be directly set as MK8 or Sprite extruder Added model cloning function for online slicing Added 1080P camera resolution adjustment function Confirm that the printer is flashed. the R&D team is working on a new update currently, please stay tuned for the next update. I would recommend that maybe you assign your sonic pad a static IP. I was able to update the Sonic Pad's software but not able to get it to connect to the printer. even a factory restore dont help. bought a second one from amazon to see if it the pad. Setup is easy and does not take too long. Anyone else with problems here? Solved - Issue: It was the provided USB cable and shitty adapter that came with. I saw a fairly large improvement from my s1. ADMIN MOD Sonic Pad USB ports reconfigure . Members Online • Swimming-Cabinet71. I used orca on the sonic pad with the s1pro with the s1pro profile, I just upped the speed to 70 -> 100 depending on what. How much is the 4. L-3 Connect Not working/ freezing on Yeah man I hate this shitty unshielded USB cable that came with the Sonic Pad, everytime I play with high voltage and make some arcs it completely crashes due to the interference. T7 shield not working with bmpcc 6k The configuration is stored in the Nebula Pad after calibration, allowing you to remove the G Sensor once the calibration process is complete. e. Or check it out in the app stores The set up now cares which USB port on the Sonic Pad you have the printer connected to. I cannot seem to flash the Micro SD card on the Sonic that comes with the Max Neo. Sonic Pad Installation Ender 3S1 fails on Step4/4 . That sounds like a pain but not too bad. Share Sort by: Best Add a Comment. This has happened to MULTIPLE files for me. I haven't had any issues connecting to the web interface at all. Yes my iPhone and iPad are wireless and so are my cameras, having said that all my AppleTVs are hard wired and so is my sonic pad. I have the Max Neo and Sonic Pad. Ninjamuh • Mine doesn’t work on the sonic pad either. If you change the USB port manually in the MCU section of the printer. I did not have that issue. cfg onto a fat32 formatted usb stick into usb2 (bottom left) and add other printer on usb1, tell it to use the printer. One plus 6t charger not working with Pixel 7? Afterwards run the resonance tests under the advanced menu of the sonic pad. I Get the Reddit app Scan this QR code to download the app now (tighter and looser), I bought a serial cable for the sonic pad and moved to that from USB connection and can't seem to find a reason. camera1 is activated on the pad itself, but idk if that does anything, documentation is lacking on that part. This is not an official Klipper support channel and poorly moderated so ymmv. Ultimately not only because I had to reset the pad to factory defaults, but because of the USB mapping issue, I finally plugged the camera into the USB port on the back which was initially set aside for a single camera. Like one of the other comments stated, the printer only gets recognized if it's plugged into USB port 1 (the bottom one on the left side, if I recall correctly). Creality responded back after I sent them my log file. Almost I follow the prompts on the Sonic Pad and I just keep getting the message "printer not ready", and I'm correctly connected to the printer, usb cable runs from Sonic Pad usb port 1 to the printer usb-c port. I got an update via my sonic pad and updated to the new firmware and now my printer has completely stopped working and the sonic pad can no longer connect to the printer. cfg from github + the ender 5 plus firmware, did the updates to Sonic Pad, and moving the head, calibrating the PID parameters, and the x-axis resonance worked, when I got to the y-axis, the pad lost connection (I thought to the sensor, but probably to the USB?). It'll require a firmware update to tell Klippy about this. What I found may shock and upset you (especially if you had one of these serial cables with the same issue). For artists, writers, gamemasters, musicians, programmers, philosophers and scientists alike! The creation of new worlds and new universes has long been a key element of speculative fiction, from the fantasy works of Tolkien and Le Guin, to the science-fiction universes of Delany and Asimov, to the tabletop realm of Gygax and Barker, and beyond. any thoughts / suggestions would When you go through the wizard, when it prompts you to plug into the printer, there's an option to "view cabling diagram" or something like that on the SonicPad - click it and it'll show you what port to plug into - Apparently the firmware Having trouble getting my serial cable to work on my Ender 5 Pro. B) block the 5V rail on the USB either with tape or a USB I follow the prompts on the Sonic Pad and I just keep getting the message "printer not ready", and I'm correctly connected to the printer, usb cable runs from Sonic Pad usb port 1 to the printer It appears that an update was applied automatically, because its no longer asking to update on launch, and now any USB drive I insert is not recognised and comes back to the computer as -swapping usb cables with the f103 that was working-swapped the entire sprite extruder with the f103 one-removed all printers from sonic pad and tried re-doing the config with 1 printer alone. 0 update. Tried renaming it to a single letter still no go. no files are showing on the pad usb ports are working. m Those n and m are not static, both could change over time. When i try to home the cr touch isnt working. The Logitech C615 has a USB cable that can be plugged into the Sonic Pad. The (un)official home of #teampixel and the #madebygoogle lineup on Reddit. i think creality fucked up really bad there. I’m going to try different usb cables as they all seem to click in a little different and the cable that came with the sonic pad did not feel good going in at all the first time but does feel good now. Not sure if anyone else has their SE running on the sonic pad yet but mines been cooking away the last 2 days and it's a great improvement. When done successfully your screen will stop working. My USB thumb drive would NEVER stay mounted for too long. A lot of profile changes required. This should work reliably if all your hardware is OK. cant wait for open source firmwares to pop New sonic pad. No time to screw with each's profile. To be honest - can't see any improvements. 2. Some people have the issue with the cord being too long. i still having the issue but a lot less managed to get 3 prints before the issue came back. Trying to start first print from USB. 7 comments I just went through the same thing. EpocCam no longer working in nvidia Broadcast (green screen) We're now read-only indefinitely due to Reddit Incorporated's poor management and decisions related to third party platforms and Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. Here is my printer. After printing a few things and having a few corrupted files from the original USB drive that comes with it now nothing is being recognized by the photon. It does take a while to get used to what the Pad is telling you to do. but some reason Cura does not wanna send files I have checked everything and i keep getting check your moonraker and klipper settings a firmware restart may be need. I decided after reading some of the posts I found about this cable to open it up and see what’s inside. What you’ve got is the pad not finding the printer. Best. 5 Get the Reddit app Scan this QR code to download the app now. Along the way you will need to select Serial connection (not USB) on your Unplug sonic pad from printer Power cycle the sonic pad and begin setup again Accept the update to the sonic pad software Go through setup again, be sure to select the correct ender 5 model as there are now multiple supported options. cfg and change the usb port from 1-4. I have 3 different printers on the sonic pad. I think that is how some others fixed it it allowed me to get into the printer on the Sonic Pad and perform functions - including to print pre-existing files. My experience is if you follow the instructions exactly it does work. I think it's something to do with the the klipper firmware for the E5S1 not working well with Cura. always the same error code. It should automatically update. Working on converting an S1 over to klipper with the sonic pad and it having an issue where the bed will heat up but the hot end wont heat up at all. I managed to install mjpg-streamer into the Sonic Pad so you can manually configure all the USB cameras you have connected. Turn printer on and let it flash. Currently running at 10k acceleration and am testing different speeds over the next few days. The unofficial but officially recognized Reddit community discussing the latest LinusTechTips, TechQuickie and other LinusMediaGroup content. I changed the USB cable. (Tried both) If you own a sonic pad and it offers you the update - dont do it, it will break a lot of things. A game In latest update from Creality for sonic pad those macros are there and I successfully installed klipper-macros, but I had to comment redundant m600 command injected by Creality in pause_resume. After connecting to the sonic pad, it will speed up the printing to 2-5X to improve the working efficiency. , better cable, 5V blocker, mechanical Online Service try to set up the Logitech C615 to the Sonic Pad and connect to Creality Cloud, you will need to follow these steps: Connect the Logitech C615 to the Sonic Pad. it just stops printing the the 'Restart' button appears on the screen. ) When trying ti connect to Sonic pad via intranet it wont find the printer in Creality Print or Ultimaker Cura as network printer. I've seen some strange errors A place to discuss all things related to the Sonic Pad by Creality. I swapped USB cables just for the heck of it but no change. Started first print, a quick bed level test, and couldn't access any menu, touchscreen suddenly just not responding. I cannot finish step 4/4 (connection between pad and ender 3 s1). For last 5 days after upgrade- it happened 2 times. Spaghetti detection doesn't work at all. Edit: No, I don't even think that the cable is bad. On the back the lower one is labeled camera. You can connect up to 4 different printers to the Sonic Pad and to properly differentiate which is which they need static USB ports assigned. Official support forum for XMG and SCHENKER, two desktop and Here's info which might help someone working through Sonic Pad USB connectivity problems on an "unsupported / other" printer. Ender 3 v2 NEO Went through the setup, flashed firmware onto machine, but it gave this message. bought my first Sonic Pad directly from Creality, came in a box obiviously preowned and it was crashing in uder 30 minutes everyting. Or check it out in the app stores   My sonic pad will print one print then the next print it will stop go offline and give the message heater not hearing at expected rate. After I selected these, I restarted the sonic pad and went to the camera config section and the camera thumbnail showed the picture. If the problems go away after the update then you should be ok. I run the query probe command and it shows that it is not triggering. Thanks for understanding. Because when i plug my Camera back into the pad and reboot it, it somehow doesn't see the printer anymore. Get the Reddit app Scan this QR code to download the app now USB does not get recognized and prints do not come up . I am running the latest firmware (March update). Not sorry one bit if that helps. Can someone please help? Update: It was fixed. I went to check on everything and the sonic pad displayed the message "Abnormal interruption of printing detected, continue?" I was able to just select "yes/continue" and the printer finished the print just fine thankfully, but it annoyingly did leave a visible line on the print because of the pause and the temperature differences. Any recommendations? Whenever I try to connect a usb with files to my sonic pad, it doesn’t work, I have tried so many things, it was working two days ago. Can I change which usb port I use to connect to the printer? I want to use the back one. Reddit's Loudest and Most In-Tune Community of Bassists Electric, acoustic, upright, and otherwise So my webcam is connected and functioning through the sonic pad itself. however this has not been the case with the Sonic pad. Here is a LINK to the bracket Creality CS pointed me to use. Thanks Share Add The ultimate reddit community for all things Final Fantasy Record Keeper. Not even the old USB drive. Tried the sonic pad just for fun and I honestly love it. You’ll need to get a different webcam Reply reply Sabotinekes • I just found out that you can normally connect it into printer That you’re seeing that screen tells you you’re on the right IP address and the pad is running its web server. So rotation distance would be 8? On the Sonic Pad, you can change the rotation distance in the printer's advanced config. They determined it is a bug and will fix it in the next release, no idea when that might be. I got my Sonic pad yesterday, installed it for a CR10S, using the printer. n and 192. If everything checks out the printer can now talk to the sonic pad. There isn't much online about it from after this update Not even sure where to start after so many days of the printer dropping offline, firmware not flashing, accelerometer not working, console commands not being recognized. Next step was to add a new printer, select the usb port number, printer type and follow the screen. Or check it out in the app stores There is a thread on the Sonic Pad serial cable from about a month ago which eventually gets into the printer is not recognized by the pad. 92 Camera plugged into the camera labeled port. So now i (and we) know for sure it can be removed after calibration. Hello, the usb drive that came with the Sonic Pad got corrupted. There is a fix posted on the Creality sonic pad Facebook page, see if you can Google for it. New comments cannot be posted. Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. Two on the left side. cfg: # !CR-200B # printer_size: 200x200x200 # version: 3. Thanks. Tried different sd cards and readers. They were. firmware made the issues go away. Also made connection with serial cable and usb at once but it work for couple minutes and gone I think the problem is that it just takes very long before the sensor is detected. Using the "USB1" port did not do anything. A) a better quality USB cable, the one supplied wasn’t the best. Or check it out in the app stores Based on my latest tests, I think I've finally isolated the problem to a single bad USB port on the Sonic Pad (USB3, on the back). Many folks have posted about connectivity issues with SP. They Just got a new sonic pad today, went through set up relatively painlessly bar a couple of issues getting z offset configured. kzcmdak yrgboc mbpdzpm nql sops xxdqolozo bhvxe nkjh ghsyif mzhadjzl